WPCA  2BJ Z CourierCourierCG TimesCG Times BoldX@`7X@HP LaserJet 4LHPLAS4L.PRS4x  @\-RX@z .,., USUK 3'3'Standard6&6&StandardrJet 4Lzư 2CEZdz.#|ECG Times BoldHP LaserJet 4LHPLAS4L.PRS4x  @\-RX@z2t%.#|E18-08-94 10:03a 1  AlineanummerRecht-Lijnende Alinea-nummerss>@ I.     %" BibliografieBibliografie4  X%" 2 aa  SubKopingSubkoping0\ E A.  VolgbladKoptekst voor een genummerd volgbladP%    X X` hp x (#%'0*,.8135@8: ! 0  X 6.7)  Y  6.8 ) Combine existing 6.7 and 6.8 as follows:  YI  "6.8: : " * Segregation and decontamination  Yz 6.8.1: : " *Substances marked .....(Text of existing 6.7) : : " * 3  Y 6.8.2 : : " *A railway wagon .......(Text of existing 6.8)" (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y  Table 6.1: Amend the title as follows: : : "  Y# 7 Table 6.1:  *LIST OF COMMON PESTICIDES WITH CORRESPONDING UN NUMBERS%  Yl  Note: : : " *The UN numbers provide a reference to the relevant proper shipping names.% 7Delete the 4 right columns of the table relating to packing groups.% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  X  Division 6.2 INFECTIOUS SUBSTANCES  Y-  6.9 (a) Renumber as 6.9.1 and amend to read: % 7"6.9.1 Infectious substances are those substances known or reasonably expected to contain pathogens. % F: : "%: 7Pathogens are defined as microorganisms (including bacteria, viruses, rickettsia, parasites, fungi) or recombinant microorganisms (hybrid or mutant), that are known or reasonably expected to cause infectious disease in animals or humans.% 7However, they are not subject to the recommendations for this division if they are unlikely to cause human or animal disease."%$!B+%%Ԍ Y ԙ 6.9 7Delete the note following 6.9 (a). %  X  (contd) (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Ya  6.9.2 Insert a new paragraph 6.9.2 to read:%  Xz  (new) 7"6.9.2 Infectious substances should be classified in division 6.2 and assigned to UN 2814 or UN 2900, as appropriate, on the basis of an assessment whether the substance is capable of spreading disease, in which assessment the following factors should be considered: %   Y : : " *the probability that the substance contains a pathogen, %  Y : : " *the concentration of pathogen that the substance may contain,%  Y" : : " *the amount of the substance to be transported,%  Y: : : " *the properties of the pathogen (i.e. risk group */) and the mode of transmission.% 7The criteria for each risk group according to the level of risk are as follows:% 7S: : "":  Y 7S: : "(a) *Risk Group 4: a pathogen that usually causes serious human or animal disease and that can be readily transmitted from one individual to another, directly or indirectly, and for which effective treatment and preventive measures are not usually available (i.e., high individual and community risk).%: 7S: : "%:  Y* 7S: : "(b) *Risk Group 3: a pathogen that usually causes serious human or animal disease but does not ordinarily spread from one infected individual to another, and for which effective treatment and preventive measures are available (i.e., high individual risk and low community risk). %: */ Text of existing footnote.  "B+%%  Y  6.9.2 S: : "(c) *Risk Group 2: a pathogen that can cause human or animal disease but is%:  Y  (contd)F: : " unlikely to be a serious hazard, and, while capable of causing serious infection on exposure, for which there are effective treatment and preventive measures available and the risk of spread of infection is limited (i.e., moderate individual risk and low community risk).%:  Y  7S: : "Note: Risk Group 1 includes microorganisms that are unlikely to cause human or animal disease (i.e., no, or very low, individual or community risk). Substances containing only such microorganisms are not considered infectious substances for purposes of these Recommendations#c'.-)-)Ԍ(Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y0  6.9 (b) Renumber as 6.9.3. (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Yy  6.9 (c) Renumber as 6.9.4 and amend to read: F: : "#: 7"6.9.4 Biological products are those products derived from living organisms, that are manufactured and distributed in accordance with the requirements of national governmental authorities which may have special licensing requirements, and are used either for prevention, treatment, or diagnosis of disease in humans or animals, or for development, experimental or investigational purposes related thereto. They include, but are not limited to, finished or unfinished products such as vaccines and diagnostic products.# # 7Note:: : "Some licensed biological products may present a biohazard in certain parts of the world only. In that case competent authorities may require these biological products to comply with the requirements for infectious substances or may impose other restrictions." #  Y  (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y  6.9 (d) Renumber as 6.9.5 # 7After "or investigation purposes" insert "or for use in medical treatment."# (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y  6.9 (e) Renumber as 6.9.6 and amend to read:#  7"6.9.6: : "For the purposes of these Recommendations biological products and diagnostic specimens ar#.%: : : "(Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y#  6.9 (b) Renumber as 6.9.3 (Subparagraphs (i) to (iv) to be relettered (a) to (d). (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Yl  6.9 (c) Renumber as 6.9.4 and amend to read: F: : "%:  Y 7"6.9.4 Biological products are those products derived from living organisms, that are manufactured and distributed in accordance with the requirements of national governmental authorities which may have special licensing requirements, and are used either for prevention, treatment, or diagnosis of disease in humans or animals, or for development, experimental or investigational purposes related thereto. They include, but are not limited to, finished or unfinished products such as vaccines and diagnostic products.% %  YG 7 Note: : : "Some licensed biological products may present a biohazard in certain parts of the world only. In that case competent authorities may require these biological products to comply with the requirements for infectious substances or may impose other restrictions."  Y  (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)%  Y  6.9 (d) Renumber as 6.9.5. After the words "or investigation purposes" insert "or for use in medical treatment." (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1) !$#B+%%  Y 6.9 (e) Renumber as 6.9.6 and amend to read:   Y1 7"6.9.6: : "For the purposes of these Recommendations, biological products and diagnostic specimens are divided into the following groups:% F: : "%: 7(a) those known or reasonably expected to contain pathogens in risk groups 2, 3 or 4 and those where a relatively low probability exists that pathogens of risk group 4 are present. Such substances should be classified in Division 6.2 under UN2814 or UN2900, as appropriate. Specimens transported for the purpose of initial or confirmatory testing for the presence of pathogens fall within this group;% 7S: : "%: 7(b) those where a relatively low probability exists that pathogens of risk group 2 or 3 are present. Specimens transported for the purpose of routine screening tests or initial diagnosis for other than the presence of pathogens fall within this group;% 7S: : "%: 7(c) those known not to contain pathogens."% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y  6.9 (f) Renumber as 6.9.7.% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y  6.10.1)  Y  6.10.2) In the first sentence delete the word "all".M% 7In the second sentence amend the reference to "6.9 (e) (ii)" to "6.9.5 (b)"% 7In the second sentence replace the words "should meet all the provisions for infectious substances except" by "need not meet the provisions for infectious substances"% 7In (d) amend the reference to "6.13" to "6.13.1"% (Doc. Ref. ST/SG/AC.10/R.497)  Y  6.11 Renumber text "The transport of...should be taken" as 6.11.1 Amend the existing section heading to read:  Y# "6.11: : " Responsibility of consignor of infectious substances " $$B+%%Ԍ Y  6.11 (a) Renumber as 6.11.2.  Y  6.11 (b) Renumber as 6.11.3.  Y2  6.11 (c) Renumber as 6.11.4.  YK  6.11 (d) Renumber as 6.11.5. (Doc. Ref. ST/SG/AC.10/R.497)  Y  6.12 Renumber text "Consignors of infectious...animals during transport" as 6.12.1 Amend the existing section heading to read:  Y "6.12: : " General packing requirements and communication of information "  Y  6.12.1 Renumber as 6.12.2.  Y  6.12.2 Renumber as 6.12.3.  Y(  6.12.3 Renumber as 6.12.4.  YA  6.12.4 Renumber as 6.12.5. (Doc. Ref. ST/SG/AC.10/R.497)  Y  6.13 Renumber text "A packaging should include...dimension of 100 mm" as 6.13.1. 7Amend the existing section heading to read: %  Y 7"6.13: : " Packing requirements "%  Y  6.13.1 Renumber as 6.13.2 and amend to read: "Inner packagings containing infectious substances should not be consolidated with inner packagings containing unrelated goods." % (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3)  YM  6.13.2 Renumber as 6.13.3.%  Yf  6.13.3 Renumber as 6.13.4.%  Y  6.13.4 Renumber as 6.13.5.  Y  6.13.5 Renumber as 6.13.6. 7Insert a new subparagraph (b) as follows:% 7"(b) The code designating the type of packaging according to the provisions of 9.4."% Renumber the existing subparagraphs (b) to (e) as subparagraphs (c) to (f).% (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3))$%B+%%Ԍ Y ԙ 6.13.6 Renumber as 6.13.7 and amend example to read: "4G/Class 6.2/92"% Amend the reference "6.13.5 (a), (b), (c)" to read "6.13.6 (a), (b), (c) and (d)". 7Amend the reference "6.13.5 (d), (e)" to read "6.13.6 (e), (f).% (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3)  Y  6.14.4 (b) Amend to read: 7"The sample should be subjected to a water spray that simulates exposure to rainfall of approximately 5 cm per hour for at least one hour. It should then be subjected to the test described in (a)."% (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3)  Y  6.14.6 Renumber existing paragraph 6.14.6 as 6.14.7. Insert a new 6.14.6 to read: 7"6.14.6 The competent authority may permit the selective testing of packagings that differ only in minor respects from a tested type, e.g.  b smaller sizes of inner packagings or inner packagings of lower net mass; and packagings such as drums, bags and boxes which are produced with small reductions in external dimension(s)."% 7(Doc. Ref. ST/SG/AC.10/C.3/14, Annex 2)%  Ys  6.14.7 Renumber existing paragraph 6.14.7 as 6.14.8 and amend the second sentence to read: 7"Such waste should be transported in rigid, leakproof packagings or IBCs, in accordance with the provisions of Chapters 9 or 16 for solids, at the Packing Group II performance level, provided there is sufficient absorbent material to absorb the entire amount of liquid present and the packaging [or IBC] is capable of retaining liquids."% (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3) $&B+%%Ԍ Y  ę 6.14.9 Add a new paragraph 6.14.9 to read:  X  (new) 7"6.14.9 Inner receptacles of any type may be assembled within an intermediate (secondary) packaging and transported without testing in the outer packaging under the following conditions:% 7(a) The intermediate/outer packaging combination should have been successfully tested in accordance with 6.14.4 with fragile (e.g., glass) inner receptacles;% 7(b) The total combined gross mass of inner receptacles should not exceed one half the gross mass of inner receptacles used for the drop test in (a) above;% 7(c) The thickness of cushioning between inner receptacles and between inner receptacles and the outside of the intermediate packaging should not be reduced below the corresponding thicknesses in the originally tested packaging; and if a single inner receptacle was used in the original  bv test, the thickness of cushioning between inner receptacles should not be less than the thickness of cushioning between the outside of the intermediate packaging and the inner receptacle in the original test. When either fewer or smaller inner receptacles are used (as compared to the inner receptacles used in the drop test), sufficient additional cushioning material should be used to take up the void;% 7(d) The outer packaging should have successfully passed the stacking test in 9.7.6 while empty. The total mass of identical packages should be based on the combined mass of inner receptacles used in the drop test in (a) above;% : : " 7(e) For inner receptacles containing liquids, an adequate quantity of absorbent material to absorb the entire liquid content of the inner receptacles must be present;% : : " *% 7(f) If the outer packaging is intended to contain inner receptacles for liquids and is not leakproof, or is intended to contain inner receptacles for solids and is not siftproof, a means of containing any liquid or solid contents in the event of leakage should be provided in the form of a leakproof liner, plastics bag or other equally effective means of containment;% : : "#'i)$$Ԍ Y  6.14.9 S: : "[(g) In addition to the markings prescribed in 6.13.6 (a) to (e), packagings should be%:  Y  (contd) marked in accordance with 6.13.6 (f)]".% (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3)  Yb  6.15 7Renumber text as 6.15.1.% 7Amend section heading to read:%  Y 7"6.15: : " Responsibility of carrier "D%  Y  6.16 7Renumber text "The consignee...avaiable to him." as 6.16.1.% 7Amend section heading to read:%  Y 7"6.16: : " Responsibility of consignee "M%  Y& 6.16.1 Renumber as 6.16.2.  YW  6.17 7Renumber text as 6.17.1.% 7Amend section heading to read:%  Y 7"6.17: : " Action to be taken in the event of damage or leakage "DDp%  Y  6.18 7Renumber text as 6.18.1.% 7Amend section heading to read:%  Y 7"6.18: : " International notification "D%  X  CHAPTER 8: SPECIAL RECOMMENDATIONS RELATING TO CLASS 8  XK  Paragraph  Y{  8.2 In footnote 1 amend reference "6.4.1" to read "6.3.2" (Doc. Ref. ST/SG/AC.10/C.3/R.497)  Y  8.3 Delete the word "animal". (Doc. Ref. ST/SG/AC.10/C.3/14, Annex 2)   #(U*%%  Y 8.4 (b) Add the following sentence at the end:  Y1 "An acceptable test is prescribed in ASTM G3172 (Reapproved 1990)". x (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3)   Y  CHAPTER 9: GENERAL RECOMMENDATIONS ON PACKING  Y  Paragraph  Y  9.1.4 The reference "(See Chapter 10)" should be replaced with "(See Chapter 4)".  Y$ [9.1.6In the first sentence, after "infectious substances", insert "(other than waste clinical or (bio)medical substances)" and replace the word "and" between "9.2" and "9.3" with a comma; at the end of the first sentence, add "and 9.4".]%  Y  9.1.9 Add a new paragraph 9.1.9 to read as follows:  X  (new)   Y "9.1.9: : "Damaged, defective or leaking dangerous goods packages, or dangerous goods that have spilled or leaked may be transported in special salvage packagings mentioned in 9.7.1.11. [This does not prevent the use of a bigger size packagings of appropriate type and performance level under the conditions of paragraph 9.3.15]"% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)   Y]  9.2.1 After the definition of "Inner receptacles" add the following definition:%  Y "Intermediate packagings are packagings placed between inner packagings, or articles, and an outer packaging."% 7After the definition of "Reused packagings" add the following definition:% #)U*%%  Y  9.2.1 "Salvage packagings are special packagings conforming to the applicable provisions of this%  Y  (contd) chapter into which damaged, defective or leaking dangerous goods packages, or dangerous goods that have spilled or leaked, are placed for purposes of transport for recovery or disposal."% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y  9.3.10 In the table of examples (8th column), replace "under para. 9.7.5.5" with "9.7.5.4(c)". (correction).  Y 9.3.11 Amend to read: "An empty packaging that has contained a dangerous substance should be treated in the same manner as is required by these Recommendations for a filled packaging, unless  Y% adequate measures have been taken to nullify any hazard."g% (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3)  Ym  9.3.15 Renumber existing paragraph 9.3.15 as 9.3.16. Insert a new paragraph 9.3.15 to read as follows:  Y 7"9.3.15 *Appropriate measures should be taken to prevent excessive movement of the damaged or leaking packages within a salvage packaging and when the salvage packaging contains liquids, sufficient absorbent material should be added to eliminate the presence of free liquid."% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)%  YF  9.4.3 Amend to read: "In the case of combination packagings and packagings described in 6.13, only the code number for the outer packaging should be used." % (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3)  *U*%%  Y 9.4.4 Amend the first three sentences in paragraph 9.4.4 to read:% % 7"The letter 'T' or 'V' or 'W' may follow the packaging code. The letter 'T' signifies a salvage packaging conforming to the provisions of 9.7.1.11. The letter 'V' signifies a special packaging conforming to the provisions of 9.7.1.7." (Remainder of paragraph 9.4.4 unchanged, except the reference to 9.3.15 which should become a reference to 9.3.16). % (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y  9.4.7 Introduce aluminium jerricans in the table of assigned types and codes of packagings as  Y follows: *% In entry "3. Jerricans" between "A. Steel" and "H. Plastics" insert: "  Y: B. Aluminium 3nonremovable headM3B1  YR : : " * 3AAV^gDDp9.6.3  Yj : : " * 3removable headM3B1 AAV^ " (Doc. Ref. ST/SG/AC.10/C.3/14, Annex 2)   Y  9.5.2.1 After "ISO 3574: 1986", amend to read "for steel" (delete the word "drums") (correction).  Y 9.5.8 Insert a new paragraph 9.5.8 (before the Note) to read:  X,  (new)  YD 7"9.5.8: : "Example of marking for salvage packaging:%  Yt : : " *u 31A2T/X300/S/94Mas in 9.5.1 (a),(b),(c) and (e)  Y : : " *n 3USA/abcDMas in 9.5.1 (f) and (g)" (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1) In the Note before 9.6, replace "in 9.5.6 and 9.5.7" with "in 9.5.6, 9.5.7  Y  9.6.3 Amend to read:  W: Metal jerricans   Yj 3A1: : "steel, nonremovable headD3B1 aluminium, nonremovable head  Y 3A2: : "steel, removable headD3B2 aluminium, removable head (Doc. Ref. ST/SG/AC.10/C.3/14, Annex 2)   Y  9.6.3.1 Amend to read: 7"Body and head should be constructed of steel sheet, of aluminium at least 99% pure or of an aluminium base alloy. Material should be of a suitable type and of adequate thickness in  Y+ relation to the capacity of the jerrican and to its intended use."g% (Doc. Ref. ST/SG/AC.10/C.3/14, Annex 2)   Ys  9.6.3.2 Amend to read: 7"Chimes of all steel jerricans should be mechanically seamed or welded. Body seams of steel jerricans intended to contain more than 40 litres of liquid should be welded. Body seams of steel jerricans intended to contain 40litres or less should be mechanically seamed or welded. For aluminium jerricans, all seams should be welded. Chime seams, if any, should be reinforced by the application of a separate reinforcing ring.%#+U*%%Ԍ(Doc. Ref. ST/SG/AC.10/C.3/14, Annex 2)   Y0  9.6.3.3 Amend to read: 7"Openings in jerricans (3A1 and 3B1) should not exceed 7 cm in diameter. Jericans with larger openings are considered to be of the removable head type (3A2 and 3B2). Closures should be so designed that they will remain secure and leakproof under normal conditions of transport. Gaskets or other sealing elements should be used with closures, unless the closure is inherently leakproof."% (Doc. Ref. ST/SG/AC.10/C.3/14, Annex 2)   Y  9.7.1.11 Add a new paragraph 9.7.1.11:  X"  (new) "9.7.1.11 Salvage packagings (see 9.2.1) should be tested and marked in accordance with the provisions applicable to packagings intended for the transport of solids or inner packagings, except as follows:%   Y 7(a): : "The test substance used in performing the tests should be water, and the packagings should be filled to not less than 98% of their maximum capacity. It is permissible to use additives, such as bags of lead shot, to achieve the requisite total package mass so long as they are placed so that the test results are not affected. Alternatively, in performing the drop test, the drop height may be varied in accordance with 9.7.3.4(b).%  Y* (b)F: : "Packagings should, in addition, have been successfully subjected to the leakproofness test at 30 kPa, with the results of this test reflected in the test report required by 9.7.8; and%:   Y 7(c): : "Packagings should be marked with the letter 'T' as described in 9.4.4."% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Y!  vN  9.7.2.5 Amend first sentence to read: S: : "%: #,U*%%Ԍ7"Additional steps should be taken to ascertain that the plastics material used in the manufacture of plastic drums, plastics jerricans and composite packagings (plastics material) intended to contain liquids complies with the provisions in 9.3.2, 9.6.7.1 and 9.6.7.4."% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  Xx  9.7.3.1  7In the first column of the table between "Steel jerricans" and "Plywood drums" insert  Y "Aluminium jerricans"BB<D% (Doc. Ref. ST/SG/AC.10/C.3/14, Annex 2)   Y  9.7.3.2 Subparagraphs (a), (b), (c) remain unchanged.  7Subparagraph (d): After "(see 9.6.18)", add "and". %  7Subparagraph (e): amend to read:%  7"Combination packagings with plastics inner packagings, other than plastics bags intended to contain solids or articles."%  7Subparagraphs (f), (g) and (h) to be deleted. % 7Remainder unchanged.% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  XY  CHAPTER 10: SPECIAL RECOMMENDATIONS ON PACKING FOR CLASS 1   To be deleted. (Doc. Ref. ST/SG/AC.10/C.3/R.483, Annex 5, paragraph 6)  X!  CHAPTER 11: SPECIAL RECOMMENDATIONS RELATING TO CLASS 5!-}((#(#Ԍ X  ę Paragraph  Y0  11.3.4.1 Amend the words "in case of spillage" to read as "in case of spillage or fire" (Doc. Ref. ST/SG/AC.10/C.3/18/Add.3, Annex E)   Yy  11.3.4.2 Replace last two sentences by "Type B diluents may be used for desensitization of all organic peroxides provided that the boiling point is at least 60 $C higher than the SADT in a 50 kg package".% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.3, Annex E)   Y  11.3.8.2 Amend the references "10.1.1 and 10.1.3" to read "4.8.2.9 and 4.8.2.10" % (Doc. Ref. ST/SG/AC.10/C.3/R.483, Annex 5, paragraph 7)  Y;  11.3.13.1 After the existing text insert a note reading:  Yl 7" Note: An example of a method to determine the size of emergency reliefdevices for tankcontainers allowed for organic peroxides, as required in 12.550, is given in document  Y ST/SG/AC.10/C.3/R.572 from the European Chemical Industry Council (CEFIC)."% (Doc. Ref. ST/SG/AC.10/C.3/18/Add.3, Annex E)   X  CHAPTER 12: RECOMMENDATIONS ON MULTIMODAL TANK TRANSPORT  Y3 1.For the consolidated text of paragraphs 12.1 to 12.23.2 see document ST/SG/AC.10/C.3/18/Add.4.  Y{ 2.Amend Table 12.1 in accordance with amendments adopted for Chapter 2 and as follows: For the entry UN 3252 delete the existing pressures in column (5) and replace with the following:%  Y (5)"43.0  39.0!.}((#(#Ԍ 34.4  30.5" (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3)    Y` 3.Amend Table 12.2 in accordance with amendments adopted for Chapter 2 and as follows:  Y 3.1At the beginning, add a note 14 to read: "Temperature should be maintained between 18 $C and 40 $C. Tanks containing solidified methacrylic acid should not be reheated during transport."%  Y   (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)%  Y 3.2Amend entries as follows:  YP UN 1224): : "Delete superscript "4" after the name. UN 1987)  Y (Doc. Ref. ST/SG/AC.10/C.3/16, Annex 3)    Y UN 2531: : "Add superscript 14 after the name (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1) #c P76P#   xP  (1) (2): : " * 3BB<(3)D(4)M(5)AAV(6)^(7)gDDp(8) x(9)  xP " 1199Furfuraldehydes * 3BB<6.1/IID3M2.65AAV12.5.2 A/12.7.3DDpN. x12.22.3" 4(Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  xP0 "1251Methyl vinyl ketone,  xP   stabilized9 * 3BB<6.1/I 3M4AAV6mm^N.A. gDDp12.9.3 x12.22.3" : : " * 3BB<D8 (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  xP "1695Chloroacetone, stabilized9BB<6.1/ID3M6AAV8mm^N.A.gDDp12.9.3 x12.22.3" : : " * 3BB<D8 (Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  xP8" "2295Methyl chloroacetate9 3BB<6.1/ID3M4AAV12.5.2^N.A.gDDp12.9.3 x12.22.3"8"/}((#(#Ԍ(Doc. Ref. ST/SG/AC.10/C.3/18/Add.1, Annex 1)  xP " 2542Tributylamine * 3BB<6.1/IIDM2.65AAV12.5.2^A/12.7.3DDpN. x12.22.3"""" (Doc. Ref. ST/SG/AC.10/C.3/14, Annex 2)  2t. t1n ""4|Jx ^dd,ddd,dddddd,,,,S,ddddlHHHil,ddH&SHSHSHSHTHSHSHSHHxHvT,llill,HilddddW,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,ddddddddddddddddddddddddddddddddddddddddNd!zz,,ru,rdd,oo,,,,,d,,r",,,,,,,,,,,,,,,,,,,V,dd,,,,,,,d,,,,d,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,ddddSNNNddNNNNNNNNNNNNdSd,,8VnDVVbbJDDPD\> J2J>8 &>>,,,,,,,,`` 8888,,,,,,,,,,zz&&>>>r"4|Jx ^;C]ddCCCdCCCCddddddddddCCY~~vCN~sk~CCCddCYdYdYCdd88d8ddddJN8ddddYYdYdCdddddCddddddddd8YYYYYY~Y~Y~Y~YC8C8C8C8ddddddddddYdddddsdXYXXXYYx|X~Y~Y|XddddddddC8C8C8C8oNd|8|H~8<|8dtddddHHJlLlLlLkN|H|8~8dddddddXXXd~8dJkN~8ddxddCddCCCWxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxNdddCYQQddddddFddddFCChhd44ddzzdddvooChdF"dhd9dCCzCddoddCdYds]zUvdYYCCCCz~ozoY~NYdYC8YooYdYzsdzdd~YYzozzzzNd88YYYzYzzzzCCdddddddzzzzzzzzzzzzzzzzzzzNNNNNNNdddddddddddddddddddd888888888888YYYYYYYYYYYYYYYYYYYzzzzzzzzzzzzzzzzzzzzCs~CzdYC\   pxtll\tll@\@\`L2&: . DZ"4|Jx ^;C]ddCCCdCCCCddddddddddCCdxN`xoCCCddCdoYoYFdo8Co8odooYNCodddYddddCdddddCddddddddo8dddddYYYYYN8N8N8N8oddddooooddpddddxodddXXYYXYYXddddddooL8N8N8N8r`o8P8N8ppoddXXYpLoNpLoNPDCopoopodXYXo8oYoNCdddoCddCCCWxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxNdddCdUUddddddFddddFCCssd44ddzzddd~ooCsdF"dsd9dCCzCddoddCdYds`zUvdddCCCCzozoYNYYYN8YooYdYzzdzddYYzozzzzNY88YYYzYzzzzCCdddddddzzzzzzzzzzzzzzzzzzzNNNNNNNYYYYYYYYYYYYYYYYYYYY888888888888YYYYYYYYYYYYYYYYYYYzzzzzzzzzzzzzzzzzzzzCzNzdYC\   pxtll\tll@\@\`L2X: V  h  'X  Figure 1  Figure 1 #2p}wC:# 3'3'Standard6&6&StandardHPLAS4SI.PRSx  +h'X UNITED NATIONS #ps7#   l X` hp x (#%'0*,.8135@8: